MPEG_PLAY

NAME

SYNOPSIS

DESCRIPTION

OPTIONS

-nob : causes the player to ignore and not display any B frames.

-nop : causes the player to ignore and not display any P and B frames.

-display display_name : causes the player to open the window on the display display_name.

-quality [on|off] : forces player to choose output quality over speed when on, and vice versa

when off. When quality is on, the player uses a computationally expensive IDCT and also improves playback through improved handling of half pixel motion vectors. The default can be set to on if you compile mpeg_play with the flag -DQUALITY.

-dither dither_option : selects from a variety of dither options. The possible values are:

ordered - ordered dither.

ordered2 - a faster ordered dither. This is the default.

mbordered - ordered dithering at the macroblock level. Although there is a noticeable decrease in dither quality, this is the fastest dither available.

fs4 - Floyd-Steinberg dithering with 4 error values propagated.

fs2 - Floyd-Steinberg dithering with 2 error values propagated.

fs2fast - Fast Floyd-Steinberg dithering with 2 error values propagated.

hybrid - Hybrid dithering, a combination of ordered dithering for the luminance channel and Floyd-Steinberg 2 error dithering for the chrominance channels. Errors are NOT propagated properly and are dropped all together every two pixels in either direction.

hybrid2 - Hybrid dithering as above, but with error propagation among pixels.

2x2 - A dithering technique using a 2x2 pixel area for each pixel. The image displayed is 4 times larger than the original image encoded. Random error terms are added to each pixel to break up contours and gradients.

gray - Grayscale dithering. The image is dithered into 128 grayscales. Chrominance information is thrown away.

gray256 - Grayscale dithering. The image is dithered into 256 grayscales (requires private colormap). Chrominance information is thrown away.

color - Full color display (only available on 16/24 bit color displays).

color2 - Full color display with increased size (only available on 16/24 bit color displays).

none - no dithering is done, no image is displayed. Used to time decoding process.

mono - Floyd-Steinberg dithering for monochrome displays.

threshold - Floyd-simple dithering for monochrome displays.

ppm - Write a PPM file for each frame.

-loop : makes the player loop back to the beginning after reaching the end.

-owncm : makes the player use a private colormap for the window.

-step : requires the user to press return for each new frame.

-seek offset : before playing the movie, seek to the given offset in the file (useful

for large movies). In this case -end is redefined to give the number of frames to play, and -start has no meaning. The offset should point to a Sequence or (closed) GOP header, but data will be discarded until one is found. The initial sequence header will be parsed before the seek. The skipped sections must not change the quantization matrices or the results are undefined.

-start num : Waits to start display until this frame number (previous frames are

parsed).

-end num : ends display at this frame number (except when -seek is used).

-gamma gamma_correction_param : specifies the amount of gamma correction. Default is 1.0. Use higher

values if movie looks dark and hard to see.

-framerate num : sets the framerate of the playback to num frames per second. A value of

0 indicates that the stream should be played as fast as possible. The default is to play at the rate specified in the stream (if possible). Note this is merely a framerate limiter, it will not discard frames to meet the rate.

-quiet : suppresses printing of frame numbers, timing information, and most error

messages.

-eachstat : causes statistics to be displayed after each frame. Only valid when

compiled with -DANALYSIS.

-shmem_off : turns shared memory off.

-l_range num_colors : sets the number of colors assigned to the luminance component when

dithering the image. The product of l_range, cr_range and cb_range should be less than the number of colors on the display.

-cr_range num_colors : sets the number of colors assigned to the red component of the

chrominance range when dithering the image. The product of l_range, cr_range and cb_range should be less than the number of colors on the display.

-cb_range num_colors : sets the number of colors assigned to the blue component of the

chrominance range when dithering the image. The product of l_range, cr_range and cb_range should be less than the number of colors on the display.

-no_display : dithers, but does not display, usually used for testing and timing

purposes.

NOTES

Some streams do not end with the proper sequence end code and will probably generate an "Improper sequence end code." error when done playing.

This player can play XING data files. Be aware that XING makes no use of temporal redundancy or motion vector information. In other words, they do not use any P or B frames in their streams. Instead, XING data is simply a sequence of I frames. Since I frames take significantly longer to decode, performance of the player using XING data is not representative of the player's ability.

The player does not play MPEG-1 D-frame streams, but they are a rarity.  

VERSION

BUGS

AUTHORS

Ketan Patel - University of California, Berkeley, kpatel@cs.berkeley.edu

Brian Smith - University of California, Berkeley, bsmith@cs.berkeley.edu

Henry Chi-To Ma - University of California, Berkeley, cma@cs.berkeley.edu

Kim Man Liu - University of California, Berkeley, kliu@cs.berkeley.edu

Steve Smoot - University of California, Berkeley, smoot@cs.berkeley.edu

Eugene Hung - University of California, Berkeley, eyhung@cs.berkeley.edu

Index

NAME

SYNOPSIS

DESCRIPTION

OPTIONS

NOTES

VERSION

BUGS

AUTHORS